Leaderboard

I was looking for a particular mold for a friend of mine that was made specifically for pouring this type resin baits. Didn't want to modify or build a mold. That question has been answered so any conversation about modifying or building molds is irrelevant as far as I'm concerned. One thing I've never understood about these message boards is why do people bother to read a particular post if all they want to do is gripe about it. Seems like there are much more productive ways to spend ones time. Maybe it should have been posted in the wire baits section. I've come to know quite a lot of folks here in hard baits and knew they would be helpful if at all possible. If posting this question in what some seem to consider is the wrong forum then sue me. Ben

You will need a small hot plate, you can get this at wally world or other store. Enough 1"x 6" x 3/4" to build a 12" OD square frame. We are going to use a shop vac for our suction. One 1" x 6" x 4' piece of pine lumber One 1" x 4" x 4' piece of pine lumber Four 3/8" x 2" flat angle braces 16, 1/8" x 1/8" pop rivets with back up washers. One piece of thin scrap wood, plastic or other type of material 10" x 10" One piece of what is called punch plate for vacuum bed top, 10" x 10" Some silicone caulk, some tape, (I used alum. tape) 16 dry wall screws 1 1/2" long OK, lets get started by building a 12" x 12" box for the hot plate to set in. Using the 1" x 6" lumber cut 2 pieces 12" long and 2 pieces 10 1/2" long. Cut a small notch in one of the boards for the hot plate cord to come through this will become the bottom of the box. This box is screwed together with the dry wall screws. Screw the 12" pieces to the 10 1/2" pieces. Now lets build the vacuum bed. Using the 1" x 4" piece of lumber, cut 2 pieces 10" long and 2 pieces 8 1/2" long. and screw the 10" pieces to the 8 1/2" pieces using the dry wall screws. Before screwing the last piece on use a hole saw to cut a hole in it that will fit your shop vac. The bottom of this hole should be about 3/8" from the bottom of the box we are building. We are also going to tape the 10" x 10" piece of whatever you use on the bottom of the box. We will then caulk the seams inside the box. Now tape the punch plate on top of the box. We now have our vacuum bed. Now we need to build an angle iron frame with a 10 1/2" inside dia.and a 12" outside dia. I think the pictures will explain this. The frame will match the 12" box perfect and slip down over the 10" box. Use the 3/8" x 2" flat angle braces on each corner, attach with the pop rivets and washers. Add a couple handles from a piece of dowel. This completes the construction process Now to use this, cut your plastic to form 12" x 12" and attach to the alum frame with the binder clips. Place your models on the punch plate, I use baits cut in half, and get a good right and left side. Set the temp on hot plate about theree fourths of the way, not on high. I have had not a fire but, i guess you could if it got too hot. Place the plastic in the frame over the hot plate and start the shop vac. The plastic will sag at first then tighten up then sag again, it is time to place it over the vacuum bed.

I'm posting this here because I don't know where else to post it. I just went online to Major League Fishing, and watched half of the first episode. It is exciting, almost like being there, fishing with the anglers. To me, it's worth the $3 an episode, or $18 for the whole package. Take a look. It's free to check it out.

Nah, I ain't gonna rely on how trees reproduce to determine hard vs soft woods. Balsa is SOFT, Cedar is HARD. I'll leave the reproductive categories to the pointy-headed dweebs.

And here we go again. I thought we had a thread that beat this discussion into the dirt? I didn't say anything before but, shouldn't this be in the wire section anyway? Douglas

A couple thoughts here. I live in NE and catching schooled up bass chasing shad is not real popular. I am guessing the rig will work under the right situation. But have never tried one. As far as modifying a sinker mold I don't have one to modify! Would alumilite resin work for the body? I have made one from pvc and will try it out this spring, before I go getting to crazy on this rig.