cadman

If this is what you're talking about.Then yes I can take some dimensions for you. I can give it to you in (.000) with calipers, or I can mic it for you in (.0000) with a micrometer. My mic only goes up to 1". It will be best to do this off line. Unless someone else is interested. PM me your e-mail with the specific dimensions you need, and or highlight what you want dimensioned............Ted

Bronzefly, I've had 4 Lee bottom pour pots, and they all dripped. I'm not an expert on this, but I've gone the route David has, and everything I've tried is only temporary. So now I put a small can under the pot to keep the splash of the drip contained.

I asked several of the guys that buy my matte finish, and they swear by it on certain days. I myself have mixed opinions. I did some testing at home, and this is what I've found. I topcoated some jigs with my matte finish, and put them in the bathtub. From the top they looked glossy. Then I took a another jig, and sanded the gloss off lightly and then topcoated with matte powder. I stuck this jig in the water. From the top it looked glossy also. Next I stuck my head in the water. Both jigs in the water did'nt seem that much diffferent, although the finish seemed softer. Knowhere nearly as much as they were when they were dry. So my consensus, IMHO, is to try it, it can't hurt. My testing was done in clear bathtub water, and I don't have a fish eyesight. If it catches fish for some people, who am I to argue.

Funny you should mention that. I used to have my powder on pressboard shelves. I had to switch over to steel shelves. The pressboard started to sag. My wife says I have a powder paint fetish. I just can't stop trying new colors. I also have a skirt fetish (it's not what you think). I'm talking about skirts for jigs and spinnerbaits. I have tons of those with different colors also. I used to be a normal person about 10 years ago:lol:. Then I started making jigs. Several years ago I joined TU and it got worse. Yes I'll admit it, I'm a jig junkie.

You're not the only one. I can tell you that if you buy powder by the pound non Pro-Tec expect to pay between $6 to $8/lb for colored powders. If you buy candy colors about $12 - $18/lb, and all clear top coats about $8 to $12/lb. There are also exotics, like wrinkled finish, veined powders, and grained powder in high gloss and low gloss. Price dictates on what you buy. The other drawback is this, if you buy a lot of powder you have shipping weight added.

Fernet sorry this is so late. I 'm usually very prompt in answering my post. I've been very busy, but here is some info for you that may help. The answer to you question is yes I have used them and I Technical_Guide.pdf Technical_Guide.pdf Technical_Guide.pdf Technical_Guide.pdf Technical_Guide.pdf Technical_Guide.pdf Technical_Guide.pdf Technical_Guide.pdf Technical_Guide.pdf

Does anyone know the difference between the regular and imported roller swivels that Barlow's carries. Also do any of you guys know who supplies these for Barlow's.........Thanks for the help.

My first quick answer to your question is, don

akriverrat I know this is a little late, but I am finally getting a chance to read up on all the threads and posts on TU. Also I had this ringing in my ear, like if someone was talking about me. Hi George. Now down to business. Now as far as harder of the two finishes, I will agree with George. In my opinion, Devcon 2T is the stuff for me. I have been using it for years, and I have never had a problem with it. Also I only use Devcon 2T on jigs that require 3d eyes, or per customer request. On all my other jigs, I use a powder topcoat. On jigs for myself, just paint and bake....Now you mentioned that you want to get into the artistic side of jig painting. I thought I was the only one who was a glutton for punishment, and kept on trying to push the limits with powder paint. This is what I can tell you. Based on what you posted, some of the things you want to do would be impossible with powder paint. So you are right in saying, that you will have to start airbrushing your fine details on. I will not dispute that fact. However here is some general info for you, you can keep somewhere hidden in the back of your brain as useless information...... I have painted and used well over 100 colors and brands of powder. They all work really well, some better than others. I can tell you that at one point, I wanted to make a bluegill powder painted jig. There were reds, browns, blacks yellows and blues. Before I even got into trying to use the stencils, I had a problem with colors blending. I wanted to add some blue on the jig, and evertime I did, the jig looked fine until I put it in the oven to bake it. Well when I did, the blue blended into the yellow, and made green. BTW, the same thing happens with purple. I've tried blue first and then other colors over and around it, and then different problems. So to cut this short, you can make some beautiful powder painted jigs, but powder paint does have limitations. I've tried stencils, heat tape, etc...they have their limitations to especially with heat, when everything has to be hot to get the paint to adhere. So if I were you go for it. Air brushing is just something more to learn, and expand your horizons.............

Chuck, I've attached a list of some of the powder paint companies that I use. There are literally hundreds. As far as who's powder is better to use, I stick with name brands, Sherwin Williams, Columbia, Dupont, IVC...etc. Pro-tec is excellent powder. But like you, I have been using alternatives for going on 6 years now. I just can't paying $6 for 2 oz. of powder, when I can get about a pound for that. The drawback is you have to buy in bulk. Can you store and keep 50 lb box of powder???? That's why they charge $6/lb, because majority of people have no choice. As far as types of powder, there are epoxies, hybrids, aromatic urethanes, aliphatic urethanes, polyester and then we go into textured, wrinkles and flats. I have used all these powders, I have mixed and blended them all with no problems. I'm not going to explain all the differences, but some of the powders I mentioned above have different qualities. Some are harder than others, some have better exterior durability, and some have better corrosion resistance. Whatever you get, will be compatible with lead. You just need to follow the MSDS sheets on heat temp. Even that is not a problem. I currently have a flat clear that I am using, and I like it very much, along with some mini-texured beige. Hope this helps some, and doesn't make it more complicated Powder Paint Manufacturers.pdf Powder Paint Manufacturers.pdf Powder Paint Manufacturers.pdf Powder Paint Manufacturers.pdf Powder Paint Manufacturers.pdf Powder Paint Manufacturers.pdf Powder Paint Manufacturers.pdf Powder Paint Manufacturers.pdf Powder Paint Manufacturers.pdf

Thanks for all the input guys.

I think he is talking about the "Hot Pot 2" made by Palmer in West Newton, PA. Javelin if that is correct, I looked at all my paperwork I got with my pots, and it doesn't mention any warranty. I would definitely give them a call, and explain to them your dilemma. I would bet, they will send you a new element. It's easy to put in. It's held in place by two screws under the top cover. Here is the link http://www.cpalmermfg.com/

Yes, you just need to buy the element, I think Barlow's has it for $17.95....+ shipping... You may want to call the manufacturere to see if it is still covered by warranty. It might be a 1 year warranty, I'm not sure.

Can you guys tell me if there is any difference in the quality of the premium smooth willow blades, that Stamina or Barlow's sells. I know there is a price difference. How is the quality of both? Thanks for the help

You have some very good points and suggestions. I

If the inside of your pvc cup is 3" in diameter like mine, I bought all my pvc lids from Menards. They were around 80 cents each. My store had around 40 of them.

Hi Mike, Welcome to TU. I know you're new here, but when you get settled in, post your questions in the wire bait section. You will get a wide variety of ideas and responses to your questions. Myself and others will be more than glad to help you out. I will tell you one thing though. Once you start getting info from everyone, you will get addictd to this stuff, if you are not already..........Now to answer your question. If you are getting paint filling your jig eye after cleaning it from painting, then you have too much paint on your jig. What's happening is this. If you are hanging your jig on you rack by the hook bend, then the excess paint is running down and covering your hook eye again. You can hang the jig by the hook eye, but now the paint will run down and bulge somewhere else. Either way it doesn't look good. Heat your jig, fluff your powder, and swish the jig through the powder. That's it.............Hope this helps. If you have any more questions, you can PM me....

Yes I do have the clear matte, yes I do have a little over 60 lbs. PM sent

I bought it from a distributor. I had to buy a 60 lb box. That's the only way you'll get any decent pricing. Sorry to say, unless you want to pay $6.00 for 2 oz. PM sent

I use a matte clear coat powder paint. It works really well for me. Made by Tiger Dry-lac powder paints.

Welcome to TU. I assume by your screen name, that you use a lot of jigs. If that's the case, then you will find a lot of good info in the wirebait section.

Neil, I guess I've already introduced myself in your first thread. Welcome to TU, where you eat, sleep, and think tackle. Where nothing else matters, ok one thing takes precedence:whistle:. It's not an addiction, it's a way of life.

Yes LedHed is correct. All your powder painting should be done first, before you bake or cure your paint. There is another TU member on here that goes by the name of Benjamin (Tj's Tackle). He has a video on powder painting and fluid bed instructions. Just something for you to see, it will definitely give you some pointers, even if you have powder painted before. Benjamin may chime in here to further assist you in your problem. Also, I can send you a copy of my tutorial, to help you out further, in powder painting.

LedHed is right about the heat gun. It will save you a lot of headaches. Also to reiterate what LedHed said!!!!!! Neil, I don

You are absolutely right. It was a guy from Australia, he went by the name of Jamie. Him and I spoke briefely about powder painting back then, and how to. I have not heard from him since. But yes pie ovens work really well. The only thing with ovens like that, is that they are big and deep. But you can do 1000's if not 10's of 1000's of jigs at a time if racked properly. There is no problem with height or depth of any jig. You can easily bake a 12" long jig on end if need be. They are readily available for commercial use. I used to work for Jewel foods back in the day, and we baked Fasano Pies. Pop I thought I had a good memory, but you do as well.