Musky Glenn

Go to You Tube and watch some videos by Marlin Baits. He makes some nice small baits.

A lot of great top water walking baits sit at a steeper angle than 45 degrees. That curly tail will really keep the bait straight and not allow to walk much. Good luck.

I've had good luck with the ones painted with uv paint, but they don't paint the larger sizes with uv paint.

I believe piano wire will rust.

I recently had a need for a large tube to dip large musky size tube baits. I had a friend to weld a bottom plate onto a short section of metal tail pipe material. I would heat the plastisol in a micro wave and pour into tail pipe and do my dipping. If you spray the inside of the tailpipe with Pam the plastic will come right out to remelt again.

Try www.dadsoletackle.com .Pretty sure they have viewable schematics. Good luck

I just noticed there are fifteen people on this forum as I type. That is the largest crowd I have been in for two weeks. We (McDowell County, NC) had our first two cases of the virus reported today. Stay safe.

The one I use doesn't lock and so far I am very satisfied with it. I did push the end off one time when emptying it. I now know how little pressure it takes to empty and haven't pushed it off again.

Maybe I don't understand McCoy's problem, but it seems to me he is not injecting hot enough if it is cooling down enough to cause a build up. My guess is he is not injecting at 350 degrees or he is picking up some "still unmelted used plastic" from bottom of liquid container. Why is 350 to hot, that is where I inject all the time. Thanks for any info.

I would get a clear schematic and see if any parts have been installed wrong, Yoke upside down, etc. I know if you put left hand gears in a 5500 right hand reel they will do the same thing. Good luck.

I used the edge of a file to cut a small notch in the end of the cylinder so I could insert a small straight screw driver and twist the nozzle out of the cylinder.

I just question the need to lock the tip to cylinder. I have pushed the end off one time into the pyrex cup when emptying the injector. Not a problem to get out of hot plastic and learned how little pressure it takes to empty injector. Haven't had it happen again. I used long needle nose pliers to retrieve tip from plastic. Good luck. I filed a small slot in the end of the cylinder for a screw driver to fit so that I could force the tip off of cylinder.

I use Bob Smith slow cure epoxy and don't thin. No problems not flowing out. I would guess you applied to thin and drug it out to much so there wasn't enough to allow flow out.

Gate shears is what your looking for. Good luck

Mark, Welcome to the world of Musky fishing. I once made a copy of a heavy musky lure out of plastic to reduce weight in casting. I made the lure hollow so it would fill up with water when in the water then immediately drain the water out for casting. Principle worked great but I just couldn't get the action exactly like I wanted.

Those might be a smidge small at 3.5". The ones I am making are 8" long and 1.5" in dia.

Upon using my tailpipe tube for an extended period of time I learned of several draw backs. First, the diameter may be to small as plastic tends to solidify to the sides of the pipe giving less room for dipping. Any touching of the sides causes terrible deformity to the dipped tube. Second, the best way is to let the dipped plastic cool between dips which also causes the plastic in the tube to harden also. This means cleaning out the pipe and remelting the plastic. It is an easy cleanup but still time consuming. Some type of controllable heat source might be an answer but I suspect controlling it would be hard as you only have a small temp window from approx. 315-375 degrees and I suspect this would cause hotter temps on bottom which would mean some type of stirring mechanism. It does make a nice product at a high cost of labor. In my situation it took two cups of plastic to fill pipe to working depth but it only took 1/4 cup to make the tube. I am a one man operation making for my self so two cups of each color takes more plastic than I want to commit to a project. I had thought about making all of them white then dipping in dye for what ever color I want.

I have cut them from an old feeler gauge. Good luck.

2.5 " tail pipe material with a plate welded on one end makes a good place to hold liquid plastic for dipping musky size tubes. The tube baits are 8" by 1.5". Spray Pam inside of pipe to help in release of plastic for clean up. I do not sell lures. I just thought this might help someone else.

You have found some, what different type blades do you want?

Check pages 142 and 143 for deep cup # 8 blades. These are .040" and there are two or more types. Did you google to find any? They are not hard to find if you look around. Good luck. Musky Shop cat. from the 2018 cat. It may be on a different page on their current cat. You can view their entire cat. on line.

You are right the Mogambo is six inches, but right beside it is the eight inch Octogambo, and beside that is the ten inch Big N Grubs all made by Kalins. This was taken from the 2018 Musky Shop Cat. They also have # 8 deep cup blades.

I have run number 8 willow leaf blades on one ounce musky spinner baits with out any problem. With that large a blade I suspect you may be opening the split ring to much and stretching it open to far. I usually run 6 and 8 size together and slow roll most of the time. The problem with the deep cup is they create such a harder pull which makes them run shallower. I believe the Musky Shop sells a Mogambo grub that may fill your need and save you hundreds on molds. Good luck

Mine don't have the pins but I have only pushed the end off one time and it didn't fall into the plastic because the plastic , around the outside where I had dipped, held it together. I just applied to much pressure when emptying after making a pour. I found my tips fit a little tight so I filed a notch into the end of the tube so I could open them with a straight screw driver.

Dadsoletackle seems to have the parts, at least they list the handle for $16.99.