OIR

still in test: took 2x 300 ml glass plastisol and heat it up to 40 degrees (hand hot 1min/200of700 microwave). took one and put it into the ultrasonic water (hand hot water) and gave it 10 min. the ultrasonic plastisol in Vacuum (3x3 min) made only 3-4 bubbles in total..!! the regular plastisol (3x3min) made the same number of bubbles as it usually does. put the 2 glass in the microwave 2 minutes on 400 (400 of 700 settings.) and microwave it 2 minutes/1 minutes/30sec/(500)30sec/30sec/30sec~ (the ultrasonic was 10 °Celsius in front of the reg all the time.) the ultrasonic hit 165 °Celsius and looked clear the regular plastisol was still in gel form..!! made the same attempt 3 times.(reg.plastisol in gel all 3 times) shot the ultrasonic in a mold..came out ..perfect (I feel like it was more running) the regular plastisol (after microwave it to 170~) came out..good (feels like regular running) the good news is the ultrasonic just take longer to harden up (but still softer vs reg. after 7 days) (from the cold test) that's what I've done so far.

plastisol in a ultrasonic cleaner make it softer and easy and cook on lower microwave settings. but is makes micro air bubbles (only made 2 test in cold water) still need a few test in hot water and Vacuum it..

https://vk.com/luresoftfishing do sell the paint. I got this ...but got no ide how to translate it.

I can give a few tips: 1. get the big laminating block not (never) the small one 2. some dual injector are "crosseyes" (take of the o-rings an see if the 2 piston aree center in the pipes) helps if you use a drill and use it to grind an oval hole toward the center we are talking about 1/10 part of a mm or lees..it helps a lot.

https://youtu.be/mCN2BGy9lL0 how to and tips: 2x Reusable plastic Cup (one cut 30 mm from below) 1x Air Line Union Hose Compressor Fittings/Connector Male to Male 1/8" take the m/m 1/8" and heat it up so you can make a hole in the plastic (Reusable plastic are hard and cracks if you drill it) after cooldown and remove leftover plastic on the m/m,screw it in or use instant glue now inside the cup hot glue (high temperature glue) up to the edge so the thread holds on to the hot glue. next up are: 1x Airbrush Coupling Disconnect Adapter Airbrush Accessory 1x Cordless Airbrush Air Compressor (it need to have the female 1/8") now all you need is to put the three things together and add one or 2 sides of a coffee filter and you get a powder paint cup. ------------------------------------------------------------------------------- now if you want it to be dustfree. 1x DC-DC USB Step UP/Down Power Supply Module Boost Buck Converter 5V to 1.2V/24V 1x usb power bank the wire on the fan can be: red-black-yellow red = + black = - or white stripe = - center cable is + so - in the center of the Converter and + on the + side (you can see the + vol on the other sider of it) keep the fan belov 12v. on to the box: 1x plastic box 3 legs (hot glue stick better on wood) 1x vacuum cleaner bag top arrow there I have made 2 holes and glued them together so they do not fall off. 1 pc 12v fan and part of a Reusable plastic cup..and a hole where the cup sits. now the Reusable plastic cup part in the box ,the tip is: that it is the bottom that points up. (like a cone) where I have cut the bottoms off first and adapted it so that the cup is about 5-10mm from the lid and there after hot gluing the cone-ring to the box. (take you time to hot glue it or it will drop out) to fit the vacuum cleaner bag on the fan : mark the shape and cut a square hole over the entrance. then sew it in the edge so it can be tightened over the fan. tighten it over the fan (use a little Cyanoacrylate and let it dry before tying a knot) now you can hot glue the fan to the box. (do use the big hot glue guns (high temperature glue) not the small hobby ones) do try to use a hepa vacuum cleaner bag. What the Heck Are HEPA Filters – And Why Should You Care? | Camfil USA Air Filter

well it was fun to try..but no luck (I was hoping for a small dark line)

https://custombaits.com/index.php?topic=12220.0

got a better hang of the selfmade hemway dye. this is 10 drops from a mix of 100g pigment and 450ml plastisol in 200 ml plastisol + black halo glitter

powder paint (blandes i en lille flaske med plastisol som farve..er meget stærk farve) testing out Hemway | Powder Pigment - Postbox Red / 100g (ebay) today..I let you see it later and I got Metallic Tangerine Orange in the mail..0h well.. Metallic Chalk White are more perl not snow white Metallic Tangerine Orange are spot on Metallic Purple Violet are spot on look like the pigment mix well: Orange + Violet = red pigment does not appear to settle to the bottom after 2 days( dyemix of 100g pigment+400g plastisol) the Metallic look .. I like it...its up yo you

made of the most crapy leftovers plastisol..and now its all sparkels and shiny after a dip. next job it to make a smaller and fast swap tool out of it.

the easy fix is boil em to get the bend out. https://www.youtube.com/results?search_query=boil+soft+bait

oh I forgot..

Cab Softbait Paint (made for soft bait) Vallejo (shake well) createx (good for a starter or pro) https://vk.com/luresoftfishing (soft bait forum and sell)

silicone do not stick to plastisol (but some china bait F... up the silicone..it never get hard)

brand of paint.! filter.! are you new to it.!

Vaseline is easy to remove : boiling hot water

well my first try was a Cake Straight Spatula but the air bubbles were trapped beneath. the second attempt was with a large piece of stainless steel..still air bubbles the last attempt was that i had cut iron so i have paper under the mold so why not try it (I notice that the plasticsol drops from the mold do not stick to paper..! )

overfilled the mold and put a piece of paper and a heavy weight on top cut it clean .(Surgical Scalpel Blades Carbon Steel 10# + Scalpel Knife Handle #3) (use heat if you need a shiny bag)

https://www.youtube.com/watch?v=7cKQ89YvPjM

https://bugmolds.com/soft-lure-molds/bait-molds/v675 https://bugmolds.com/soft-lure-molds/bait-molds/v513

https://www.ebay.com/usr/bekateq?_trksid=p2047675.l2559 The Ultimate Crystal Clear Cast Resin, 2 kg Epoxy Resin + 1 Harder, Transparent (As long as you use a weight to measure, all epoxy is very trouble-free)

aluminium molds are the top best white stone molds are ok pale stone mold need a lot of lube. mixed color mold are crap. Dual Color Hand Injection Kit (get the big mixing block)