OIR

airbrush/paintbrush nail dust/ pigment /mica/glitter (ebay) https://www.youtube.com/results?search_query=+paint+soft+bait

epoxy resin...! taken from : https://vk.com/luresoftfishing

as it looks overall. the screw pushes the small tube down on the washer which pushes the silicone ring out to the side so it closes tight in the pipe silicone tip nylon top (Lost the 2 O-rings when I took it apart) Black Plastic Round Handle Ball Knob M10 Threaded 40mm Dia Machine Tools (ebay) 2 washers (The bottom is welded on the threaded rod) homemade silicone ring threaded rod + bolt steel pipe (id 10 mm) seamless pipe The two nylon parts to make the silicone tip I put some tape around the block to the right and fill it with silicone and push the left part down in it. To make the ring I fill it with silicone table top bolt M10 so I can level the silicone.

got some Metallic Glitter Pearl Pigment Powder from ebay mix 100g in 500ml plastisol as dye .. 30 drops in 500ml plastisol got me this 30 yellow drops from a 30ml bottles in 500ml plastisol got me this: love the Nebula colors

works great for leftovers.

looks good.

Perforated Metal Ceiling Tiles Steel Perforated Sheet Perforated metal tray Perforated Baking Serving Tray For Oven Baguette Pans https://www.ebay.co.uk/sch/mesh-company/m.html?_nkw=&_armrs=1&_ipg=&_from= https://www.amazon.com/Expanded-Perforated-Sheets/b?ie=UTF8&node=6469722011 https://www.ebay.com/sch/i.html?_from=R40&_nkw=perforated+metal+sheets+steel&_sacat=0&LH_TitleDesc=0&ul_noapp=true&LH_PrefLoc=3 well...if you can cut it and its steel and got holes.

so silicones can run on the other side and into the small holes.so they are molded into the mold yes the hot glue stick is just to hold the plates in place. and you can remove it after the silicone is dry. 2 cm/0.78 in on both sides

lets start ... 1. build a mold (lego + steel plate and some hot glue to hold it) 2.mix up som silicone..just to hold the lure in place. and let it dry..this way the lure will stay in place put som rubber band on 2 perforated steel plate 3 put in silicone to cover the lure and the 2 steel plate 5 heat up a hot glue rod ..it will hold the 2 steel plate 6 time to turn the molde over..and cut it clean 7.build one more wall of lego and add more silicone and let it dry. 7a.take off the lego and cut it open to take the lure (only cut just what is needed to get it out) To use it: press together the 2 steel plate with one hand and pour with the other one down the crack. And slowly let go so it closes the crack. let it get cold and pli off the extra plastisol (extra: 4x Makro Filter cheap way to turn any DSLR lens into macro)

https://www.youtube.com/watch?v=5U5fa4HdzYM

25 years ago.... I was told that chalk makes the mold more hard and +10-15% resistant to heat to the left : 25 years old lead (2 part mold to the right : 4 days old (1 part mold)

use a candle let it smoke and turn the mold black it makes release eaiser and pre-heat the mold the same time. I mix in powder chalk 20% in the silicone rubber (RTV Silicone Moulding Rubber Shore A15)

"metal A necessity for turning bias tubing button loop" on ebay