jim45498 Posted October 18, 2007 Report Share Posted October 18, 2007 I have heard that some apply devcon with "pop-cicle" sticks. How in the world do you do this? Won't the devcon be thick and globby and pile up on the bait? Quote Link to comment Share on other sites More sharing options...
Skeeter Posted October 19, 2007 Report Share Posted October 19, 2007 Save yourself a ton of problem and just use a brush to apply the devcon. Trust me. Where are you in Ky? I was born and raised in Louisville. Skeeter Quote Link to comment Share on other sites More sharing options...
LooksLikeSinbad Posted October 19, 2007 Report Share Posted October 19, 2007 Save yourself a ton of problem and just use a brush to apply the devcon. How do you clean the brushes? I have been trying to clean them with paint thinner and it doesn't work very well. Quote Link to comment Share on other sites More sharing options...
clamboni Posted October 19, 2007 Report Share Posted October 19, 2007 dip and swish them in acetone for a minute or two then dry them on a towel. Make sure after you dry them that all the epoxy is out. Or you could just use cheap brushes and toss them. I like a nylon bristled brush. I don't know anything about paintbrushes, but as far as I can tell what I like is a medium stiffness brush. Make sure it won't shed bristles. Quote Link to comment Share on other sites More sharing options...
Palmetto Balsa Posted October 19, 2007 Report Share Posted October 19, 2007 It has been said before, go to the craft store and buy a container of 300 craft brushes (about $4.99) and just throw them away after you use them. I like to cut half of the handle before I used them because I felt it gave me better control. Pop-cicle stick, a cats paw, or cheap brushes, they all work fine. Quote Link to comment Share on other sites More sharing options...
clemmy Posted October 19, 2007 Report Share Posted October 19, 2007 Don't use wood such as popsicle sticks to apply or mix epoxy for clearcoat, as it can lead to bubbles (not neccessarily WILL, but it sucks if it happens!) Clemmy Quote Link to comment Share on other sites More sharing options...
jim45498 Posted October 19, 2007 Author Report Share Posted October 19, 2007 Thanks for the replys. I have been using a real soft artist brush and cleaning it in a cup with alcohol, then I pour the alcohol out and put in some fresh and let my brush soak until I need to coat another bait. So far it has worked. But I was wondering about the other ways. I like the idea of throw away brushes. Buying them by the 100 or more. You guys are really good at this and I learn something new with every visit. Quote Link to comment Share on other sites More sharing options...
Skeeter Posted October 21, 2007 Report Share Posted October 21, 2007 I use a testors model paint brush that I get at wall mart. It is about a dollar for one brush. It is the one with the metal sleeve holding the bristles. I take a paper towel and squeeze out the excess devcon. Then I put the brush in acetone to soak. When you take the brush out, give it another squeeze with a paper towel and either use it again or put it up. The bristles will seem hard once they dry. But you can just move them back and forth with your fingers and they will soften right up. I can usually do 30 baits with one brush before I have to toss it. You can still use the brush to coat jigs and stuff. But it eventually becomes to stiff to spread devcon smoothly. Skeeter Quote Link to comment Share on other sites More sharing options...
cheesehead Posted October 21, 2007 Report Share Posted October 21, 2007 I use glue or flux brushes for applying my epoxy. The bristles are stiffer so it spreads the epoxy better in my opinion. check in the plumbing department at your local hardware store. Quote Link to comment Share on other sites More sharing options...
thogan6 Posted October 21, 2007 Report Share Posted October 21, 2007 hey guys skip the devcon and start using pelucid you can find it at marine-paint .com it dries rock hard is non-yellowing and is one part. if you pour some in a shot glass you can dip the bait and hang it the best finish you will ever use for clearcoat Quote Link to comment Share on other sites More sharing options...
Skeeter Posted October 21, 2007 Report Share Posted October 21, 2007 Yeah guys... skip the Devcon!! "Can Pelucid be Buffed Out and Waxed Like Other Clearcoats? Yes, but wait several weeks after application to make sure it is fully cured." Skeeter Quote Link to comment Share on other sites More sharing options...
KcDano Posted October 21, 2007 Report Share Posted October 21, 2007 I have used por15 rust treatment and it is a superior product. I had considered using pelucid on baits, but read on their site it was a interior product. Quote Link to comment Share on other sites More sharing options...
Hoodaddy Posted October 21, 2007 Report Share Posted October 21, 2007 I've tried Pelucid and Por-15 and both items in my opinion are very tempermental. Storage seems to be the main gripe. I know that certain methods have to be taken to get the extended shelf life but my fiance does'nt like that kind of stuff in the fridge....and I'm not going to dig a root cellar . My understanding is that is the best way to store it. I switched to Dicknites a while back with encouragement from another member and after a prolonged test I'll stick with it. All the experimenting over the yrs. has brought me to where I'm finally somewhat happy with my offerings . Just my opinion............Thanks Cuz Quote Link to comment Share on other sites More sharing options...
