Jump to content
kevin24018

Hinge/joint Materials

Recommended Posts

So many ways to skin a cat er um fish I mean

Here's what I have found so far

 

Pin type hinge made in plastic and metal

screw eyes

various wire looping methods

 

now what I have seen are multi segmented  lures that don't have hinges but rather seems to be some sort of flexible material.

 

I'm not sure what it is, perhaps a rubber gasket material cut to size, and some i have seen it appears the segments are actually build or cast onto this material itself.  Was thinking about going to a junk yard and getting some seat belts, although I'm not sure they would hold together after cutting them.

 

Any one have experience using a solid type of hinge/joint?  Not sure what to call it.

Link to comment
Share on other sites

I have used 'Velcro' backing, the trick is to find something that is strong but still flexible, what seems flexible in your hand becomes quite rigid when it's only got 1/4" to move between the joints--I have used this on a 3 1/4" lures with 3 joints, so there is probably only about 1/8" gap between segments.

Pete

Link to comment
Share on other sites

Years ago I got a bait sample from a company in Cal. called Flexlure. The bait had four sections all joined by a flexible material. It was stiff enough to keep the bait in line but flexible enough to give the bait a snake-like movement. It swam very well.

Link to comment
Share on other sites

I toyed around with various materials for a little while. I even made a small loom and wove some of the braided lines to make a "cloth" strip to use.  Came down to just too much effort for no better results.  Some cables gave good results but construction methods become more important and one has to add elements to reduce wear on the bait.  I had to run small diameter pipe and flare the ends for pass trough for the cable or piano wire I was using.

Link to comment
Share on other sites

Remember all the coats and tents made of 'ripstop nylon'?  I always thought that would work well for this.  It's very tear resistant and you could sear the edges with a hot knife or something to keep it from fraying.  I haven't tried it yet but think that the trick would be to use enough glue to put the two sides together without using so much glue that it gets on the nylon 'hinge'.  If you do one section at a time you can wipe off excess glue and only have to be careful on the adjacent section.

Link to comment
Share on other sites

Remember all the coats and tents made of 'ripstop nylon'?  I always thought that would work well for this.  It's very tear resistant and you could sear the edges with a hot knife or something to keep it from fraying.  I haven't tried it yet but think that the trick would be to use enough glue to put the two sides together without using so much glue that it gets on the nylon 'hinge'.  If you do one section at a time you can wipe off excess glue and only have to be careful on the adjacent section.

 

I ended up having to essentially top coat the areas where the nylon or whatever material I was using prior.  If not the top coat get onto the material and you flex goes away or wears the material quickly as you have  rigid/limited give zone going directly to flexible material.  Works better if the flex material is a stiffer flexing material but then the action starts to get killed.

Link to comment
Share on other sites

I saw someone use the word spandex as well, but I wasn't sure if that was translated or perhaps ment something different in their language.  The spandex I remember (growing up in the 80's) was stretchy.

Hadn't thought about the rip stop nylon.  I have used some to make kites in the past and it comes in different weights etc, it's fairly cheap from what I remember, thanks everyone!

 

Hughesy those are exactly what I'm talking about, thanks. Edited by kevin24018
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...


×
×
  • Create New...
Top