jonister Posted February 28, 2016 Report Share Posted February 28, 2016 I think it would hold up to saltwater, but I don't know about bluefish. I don't have them here but have seen the damage on TV that they can do. Maybe quite a few coats would do it. The Art resin takes so long to cure that you can either heat it on a heater before or after you mix and it will be nice and thin for a minute or so. Also, the way I understand it, if your lures are leaking sealer than it has not had enough time to dry. Just my 2 cents! I'm sure someone who fishes the salt more than me will chime in. Good luck! Quote Link to comment Share on other sites More sharing options...
jigginpig Posted March 6, 2016 Report Share Posted March 6, 2016 Just ordered the small kit to test. Will post results. SS Quote Link to comment Share on other sites More sharing options...
rockdog23 Posted March 11, 2016 Report Share Posted March 11, 2016 Anyone get any on water testing with this clear? Quote Link to comment Share on other sites More sharing options...
jonister Posted March 11, 2016 Report Share Posted March 11, 2016 Right now it is still to cold really for fishing hard baits in my area but I did throw some of them and it held up great. I might bring them with me on my next saltwater outing. Maybe throw them for a bit and test how salt resistant they are. 1 Quote Link to comment Share on other sites More sharing options...
Mad Moose Baits Posted March 12, 2016 Report Share Posted March 12, 2016 I took one of my lures and put it in a plastic bowl filled with water and left it in there with lid closed for 9 hours. Now this obviously doesn't simulate bouncing off rocks, docks, toothy critters etc etc etc but I figure with the average cast maybe lasting 30 seconds this simulated the time in water for well over 1000 cats. No change. Still super clear, super glossy and I could find no softening. I can't wait to drag some cranks through the pea gravel in the river behind my house. That will be a much truer test. Quote Link to comment Share on other sites More sharing options...
rockdog23 Posted March 12, 2016 Report Share Posted March 12, 2016 How long should I wait before I apply the second coat with the Art Resin? Quote Link to comment Share on other sites More sharing options...
KevinHanses Posted March 13, 2016 Report Share Posted March 13, 2016 How long should I wait before I apply the second coat with the Art Resin? I haven't put a 2nd coat on any of my paints yet. Haven't needed to. Quote Link to comment Share on other sites More sharing options...
rockdog23 Posted March 13, 2016 Report Share Posted March 13, 2016 I must be doing something wrong then, I can't get away from the second coat, I would absolutely love to. Are you applying super thick on the first coat? Are others able to get away with one coat with this? Thanks... Quote Link to comment Share on other sites More sharing options...
KevinHanses Posted March 13, 2016 Report Share Posted March 13, 2016 (edited) I apply really thick on the first coat, then go around brushing off the excess from the nose to tail in one stroke, then wipe off the brush, and repeat. Edit: I also have a turn table they dry on. Don't know if you do, or not. Edited March 13, 2016 by KevinHanses Quote Link to comment Share on other sites More sharing options...
law651 Posted March 23, 2016 Report Share Posted March 23, 2016 I have now used some of my cranks clear coated in Art Resin.. They performed pretty awesome. Walleyes never left a scratch in the clear. I still need to make a video. I just want to thank Art Resin for the opportunity of testing their product. It does perform very well. I do like it better than Etec.. Mostly because of the application.. It goes on very well and resists fish eye much better than any other epoxy. It is very, very clear and has a very high gloss.. Very good product.. I will be ordering some just as soon as I finish my current inventory of other epoxy... Quote Link to comment Share on other sites More sharing options...
Cuttem Jack Posted March 31, 2016 Report Share Posted March 31, 2016 I just tried it last night for the first time. 9 hours later and still tacky. It is on my lure turner in an unheated garage. I'm hoping it was the temperature that has them still tacky but am getting concerned. Last night low was in 50's. Want to add second coat(musky lures) but from what I read it says to wait until first coat is completely dry. Not sure what to do. Any ideas? Quote Link to comment Share on other sites More sharing options...
ravenlures Posted March 31, 2016 Report Share Posted March 31, 2016 I am having good results with the Sherwood Williams concrete sealer (oil based) just dip after a hour 4 to 5 times each and let sit for two days and great finish. 1 Quote Link to comment Share on other sites More sharing options...
Muskie Tamer Posted March 31, 2016 Report Share Posted March 31, 2016 I just tried it last night for the first time. 9 hours later and still tacky. It is on my lure turner in an unheated garage. I'm hoping it was the temperature that has them still tacky but am getting concerned. Last night low was in 50's. Want to add second coat(musky lures) but from what I read it says to wait until first coat is completely dry. Not sure what to do. Any ideas?[/quoteGive it more time. Temps will affect the cure time. 1 Quote Link to comment Share on other sites More sharing options...
mark poulson Posted March 31, 2016 Report Share Posted March 31, 2016 I just tried it last night for the first time. 9 hours later and still tacky. It is on my lure turner in an unheated garage. I'm hoping it was the temperature that has them still tacky but am getting concerned. Last night low was in 50's. Want to add second coat(musky lures) but from what I read it says to wait until first coat is completely dry. Not sure what to do. Any ideas?[/quoteGive it more time. Temps will affect the cure time. Will hitting the lure with a hair dryer, or some other gentle heat source, speed up the curing? Quote Link to comment Share on other sites More sharing options...
Cuttem Jack Posted March 31, 2016 Report Share Posted March 31, 2016 I checked them this afternoon and could finally shut the turner off. Website says to let first coat fully dry before applying second coat. With etex I never let the first coat fully harden. What are you guys doing? Quote Link to comment Share on other sites More sharing options...
Mad Moose Baits Posted March 31, 2016 Report Share Posted March 31, 2016 (edited) Will hitting the lure with a hair dryer, or some other gentle heat source, speed up the curing? The AR folks told me using a regular lighter near the bait will do fine. *edit I also asked about hair dryers and they said the lighter is better because it doesn't blow. Edited March 31, 2016 by Mad Moose Baits Quote Link to comment Share on other sites More sharing options...
fishnart Posted March 31, 2016 Report Share Posted March 31, 2016 I dry mine in a basement and it usually takes 24 to 48 hours to completely cure. Last night I used a portable heater next to them and it may have helped a tad. It just takes time for this to cure Quote Link to comment Share on other sites More sharing options...
nedyarb Posted April 1, 2016 Report Share Posted April 1, 2016 The best solution is time, it takes 48 hours to dry. Its still tacky after 24 hours. I just use 30 min epoxy if I dont want to wait 4 days. Quote Link to comment Share on other sites More sharing options...
Cuttem Jack Posted April 1, 2016 Report Share Posted April 1, 2016 Watch what you mix this in. I had it eat through a plastic cup this morning and got it all over my garage floor. So far not impressed at all. Quote Link to comment Share on other sites More sharing options...
KevinHanses Posted April 2, 2016 Report Share Posted April 2, 2016 Watch what you mix this in. I had it eat through a plastic cup this morning and got it all over my garage floor. So far not impressed at all. Really? Haven't had that happen, yet, I guess. Sometimes I use the small plastic cups, but most of the time I use small Dixie cups. Quote Link to comment Share on other sites More sharing options...
nedyarb Posted April 2, 2016 Report Share Posted April 2, 2016 My observations are it takes a good two days to dry. And I missed a spot on a lure a few days ago, so instead of recoating it in the art resin I dipped it in kbs diamond, and the lure has lumps everywhere. Quote Link to comment Share on other sites More sharing options...
DJoseph Posted April 8, 2016 Report Share Posted April 8, 2016 How long should I wait before I apply the second coat with the Art Resin? You can actually do a second coat as soon as the first coat has firmed up enough that the next layer can sit on top.. usually 5 hours-ish. We used to say wait till full dry but tests have shown it's not necessary. ...sorry for my slow reply! we were at a trade show, busy busy! Quote Link to comment Share on other sites More sharing options...
DJoseph Posted April 8, 2016 Report Share Posted April 8, 2016 I must be doing something wrong then, I can't get away from the second coat, I would absolutely love to. Are you applying super thick on the first coat? Are others able to get away with one coat with this? Thanks... Are you dipping the lure in the resin? That's probably the best method to get all over even thick coverage... I have now used some of my cranks clear coated in Art Resin.. They performed pretty awesome. Walleyes never left a scratch in the clear. I still need to make a video. I just want to thank Art Resin for the opportunity of testing their product. It does perform very well. I do like it better than Etec.. Mostly because of the application.. It goes on very well and resists fish eye much better than any other epoxy. It is very, very clear and has a very high gloss.. Very good product.. I will be ordering some just as soon as I finish my current inventory of other epoxy... thank you sir! glad to hear it. looking forward to the video! Quote Link to comment Share on other sites More sharing options...
DJoseph Posted April 8, 2016 Report Share Posted April 8, 2016 I just tried it last night for the first time. 9 hours later and still tacky. It is on my lure turner in an unheated garage. I'm hoping it was the temperature that has them still tacky but am getting concerned. Last night low was in 50's. Want to add second coat(musky lures) but from what I read it says to wait until first coat is completely dry. Not sure what to do. Any ideas? ArtResin takes 24 hrs to cure, longer in the cold. You can add a second coat after about 5 hrs, when the resin has formed a firm layer and the next layer can sit on top. We used to suggest wait the full 24 hrs before doing a second coat but tests since have shown that's not necessary. The reason it takes 24 hr to cure is because we prioritized non-yellowing clarity and non-toxicity, and to get the non-yellowing clarity we had to pull back on the accelerating agent that causes curing to happen. That material is YELLOW and gives a yellow tinge to the entire product. We figured a little longer was worth the wait. Quote Link to comment Share on other sites More sharing options...
DJoseph Posted April 8, 2016 Report Share Posted April 8, 2016 Watch what you mix this in. I had it eat through a plastic cup this morning and got it all over my garage floor. So far not impressed at all. What! Never heard of this happening before. Sure resin heats up when it's mixed, they all do... but eating through a plastic cup? must have been a cheap cup! Sorry to hear that, nonetheless. Quote Link to comment Share on other sites More sharing options...