Fisheye48 Posted February 14, 2017 Report Share Posted February 14, 2017 I get small bubbles after adding in my color and stirring it in. I've tried letting it sit for a little and letting the air bubbles come to the top the drawing it out to inject it. Still get air in my baits. Ive tried stirring with knifes, spoons, a thick piece of stainless wire. Any help is greatly appreciated. Quote Link to comment Share on other sites More sharing options...
Walking Dead Posted February 14, 2017 Report Share Posted February 14, 2017 You using salt? Fresh plastic or reheats? Brand? Quote Link to comment Share on other sites More sharing options...
Fisheye48 Posted February 14, 2017 Author Report Share Posted February 14, 2017 no salt, fresh M-F plastic Quote Link to comment Share on other sites More sharing options...
Walking Dead Posted February 14, 2017 Report Share Posted February 14, 2017 Not any idea unless humidity, maybe? I use a spoon to stir when I use the microwave and no issues unless I am reheating some old plastic for TRASH baits. Quote Link to comment Share on other sites More sharing options...
Fisheye48 Posted February 14, 2017 Author Report Share Posted February 14, 2017 ill pm you some pics when i get home in a few hours Quote Link to comment Share on other sites More sharing options...
alsworms Posted February 14, 2017 Report Share Posted February 14, 2017 Moisture must be taken in somewhere because I've never heard of bubbling problems with MF Quote Link to comment Share on other sites More sharing options...
Baitjunkys Posted February 14, 2017 Report Share Posted February 14, 2017 (edited) Any brand plastic can get bubbles stirred in. Sounds like a injector issue to me. Edited February 14, 2017 by Baitjunkys Quote Link to comment Share on other sites More sharing options...
Frank Posted February 15, 2017 Report Share Posted February 15, 2017 I have had that happen and it sound funny but it's the colorant that does it. Some peoples colorant does that. Try and let it set and get a skin on top, remove it and inject again see if it is better. Quote Link to comment Share on other sites More sharing options...
SMX Posted February 15, 2017 Report Share Posted February 15, 2017 Fisheye are you adding the colorant before or after you heat? Quote Link to comment Share on other sites More sharing options...
jeff@mf Posted February 15, 2017 Report Share Posted February 15, 2017 Colorant will for sure add bubbles they are correct again, try without or another color, I also see glitter, and polyester molds bubble while aluminum didn't within same 5 minutes. I have seen scent do it too. Who's color? jeff@mf Quote Link to comment Share on other sites More sharing options...
jeff@mf Posted February 16, 2017 Report Share Posted February 16, 2017 Ah that's good to hear, hear that ? That's silence of the post. LOL 1 Quote Link to comment Share on other sites More sharing options...
txmedic033 Posted February 26, 2017 Report Share Posted February 26, 2017 I also get bubbles in my MF saltwater plastic. It bubbles less than the Do-It plastisol I previously used, but it does bubble. I use it to dip my swimbaits in after I apply my eyes and they routinely have bubbles on them. No color, glitter, or other additive is added. I mostly hand inject so the bubbles are rarely an issue, but they are an issue when I pour baits. Quote Link to comment Share on other sites More sharing options...
Baitjunkys Posted February 26, 2017 Report Share Posted February 26, 2017 I doubt you will ever find a brand that wont bubble eventually from one batch to another. If you do, Buy it, and keep buying it. There is far to many variables involved. Simplest solution, buy one of these. https://www.bestvaluevacs.com/bvv3g-sm-rs1.html Quote Link to comment Share on other sites More sharing options...
