mark poulson Posted February 16, 2017 Report Share Posted February 16, 2017 I am sure I bought a Do-It Arky jig mold with multiple 1/2 oz cavities, and now I don't find it on their website. Am I misremembering? Quote Link to comment Share on other sites More sharing options...
Apdriver Posted February 16, 2017 Report Share Posted February 16, 2017 Can you put your hands on it, Mark? Should have a number on it. I know they have some pro molds with multiple cavities of same size. Have a few of those. However, my Arkie mold has single cavities of multiple sizes. Quote Link to comment Share on other sites More sharing options...
Mr B Posted February 16, 2017 Report Share Posted February 16, 2017 I would like this also. Let me know if you find it. Quote Link to comment Share on other sites More sharing options...
mark poulson Posted February 16, 2017 Author Report Share Posted February 16, 2017 I'll ask my buddy for the numbers. He pours for me, I make cranks for him. 1 Quote Link to comment Share on other sites More sharing options...
cadman Posted February 16, 2017 Report Share Posted February 16, 2017 Mark, I have never seen a Do-It Arky mold with multiple cavities of the same size. I do know that Hilts mold had one years ago, as a buddy of mine had one. If you find out, I am interested as well. Especially if you find one in 3/4 oz. 1 Quote Link to comment Share on other sites More sharing options...
Mr B Posted February 16, 2017 Report Share Posted February 16, 2017 Yes 3/4 and even 1oz. LPO sells the premade heads in these sizes and I may have to buy a few to make a mold (for my personal use) but I really want to pour quantities. Quote Link to comment Share on other sites More sharing options...
mark poulson Posted February 17, 2017 Author Report Share Posted February 17, 2017 13 hours ago, cadman said: Mark, I have never seen a Do-It Arky mold with multiple cavities of the same size. I do know that Hilts mold had one years ago, as a buddy of mine had one. If you find out, I am interested as well. Especially if you find one in 3/4 oz. Ted and Mr. B, My pouring buddy is going to check the numbers on the molds and get back to me. I'll share them as soon as he gives them to me. Hazel. 1 Quote Link to comment Share on other sites More sharing options...
mark poulson Posted February 18, 2017 Author Report Share Posted February 18, 2017 Well, bad news. My buddy just emailed me to say the same size multi cavity football head molds don't have a number on them. And I was misremembering . The Arkie and Sparkie molds he has are the ones with different sizes. I guess it's just CRS again! I have no clue why they stopped making the same size multi cavity molds, but they did. The only pro series same size multi cavity molds on the Do-It site that I could find now are in the round head jigs. Sorry for raising false hopes. Quote Link to comment Share on other sites More sharing options...
cadman Posted February 18, 2017 Report Share Posted February 18, 2017 Hey Mark, No problem. Over the years I have tried on and off sporadically to pour multiple cavities in a mold. It was troublesome, due to the fact you have to load all the cavities with different size hooks. It was very cumbersome and time consuming. Then I tried to pour multiple cavities of the same size jig (ie Do-It round heads), and found it slow as well, as you still have to load all the hooks, and if one hook shifts, the mold halves won't close, so then the other hooks fall out or shift as well. That was cumbersome to me as well. Now I only pour one cavity at a time, and it seems to go very fast. Just my thoughts on it. 2 Quote Link to comment Share on other sites More sharing options...
mark poulson Posted February 18, 2017 Author Report Share Posted February 18, 2017 1 hour ago, cadman said: Hey Mark, No problem. Over the years I have tried on and off sporadically to pour multiple cavities in a mold. It was troublesome, due to the fact you have to load all the cavities with different size hooks. It was very cumbersome and time consuming. Then I tried to pour multiple cavities of the same size jig (ie Do-It round heads), and found it slow as well, as you still have to load all the hooks, and if one hook shifts, the mold halves won't close, so then the other hooks fall out or shift as well. That was cumbersome to me as well. Now I only pour one cavity at a time, and it seems to go very fast. Just my thoughts on it. That's the same thing my buddy said about pouring the Arkie and Sparkie molds. We fish mainly 3/8 and 1/2 oz, so he loads two hooks at a time, and says he goes faster than with the multi cavity 3/8 oz football mold. Have you ever tried using magnets to hold your hooks in place? Quote Link to comment Share on other sites More sharing options...
cadman Posted February 18, 2017 Report Share Posted February 18, 2017 8 minutes ago, mark poulson said: That's the same thing my buddy said about pouring the Arkie and Sparkie molds. We fish mainly 3/8 and 1/2 oz, so he loads two hooks at a time, and says he goes faster than with the multi cavity 3/8 oz football mold. Have you ever tried using magnets to hold your hooks in place? I tried magnets years ago and it didn't work for me. Any magnet on the outside of the mold would have to be strong enough to hold the hook in place . Since the molds are alum., I found that the magnet wouldn't conduct through the 1" thick alum. Any magnets on the inside would have to be very thin and permanently affixed to the mold, probably in the pocket where the hook bend sits. Taping the magnet on will not work, because of the extreme heat temp the mold gets. All the tapes I've tried did not work, because of adhesive failure. I've given this a lot of thought on and off over the years. I haven't tried everything, but so far no real inventions or light bulbs have entered my mind as of yet. 1 Quote Link to comment Share on other sites More sharing options...
smalljaw Posted February 18, 2017 Report Share Posted February 18, 2017 I agree with Cadman, pouring multiple cavities is slower for me. I tried it many times with my production ball head molds, I'd load the hooks and then over pour each cavity so I'd end up with a single large connected sprue and I'd be able to pull all the heads out at 1 time. But after I'd get all the heads I wanted done I'd spend another 45 minutes cutting all the jigs free from the sprue, between the time it took to load the mold with hook and the time spent cutting jigs free I did better pouring 1 at a time. 1 Quote Link to comment Share on other sites More sharing options...
mark poulson Posted February 18, 2017 Author Report Share Posted February 18, 2017 It sounds to me like multi cavity molds are a pain to try and pour more than one at a time. I am glad my buddy does the pouring. I do the powder coating, skirt tying, and I build/paint the cranks, but he pours like a fiend! Quote Link to comment Share on other sites More sharing options...
Basseducer Posted February 18, 2017 Report Share Posted February 18, 2017 I have a Do-It ARKY mold that has four 1/8 oz. cavities #ARK-18Y. It isn't on their site anymore, but you would think that there are other sizes out their. You can always get a mold blank and send it to http://pouritmold.com/ and have him make you what you want. 1 Quote Link to comment Share on other sites More sharing options...
walleyeking Posted February 21, 2017 Report Share Posted February 21, 2017 Do-it still lists football heads in multi cavity all one size on there website. 1 Quote Link to comment Share on other sites More sharing options...
mark poulson Posted February 21, 2017 Author Report Share Posted February 21, 2017 13 hours ago, walleyeking said: Do-it still lists football heads in multi cavity all one size on there website. You are good. I still can't find it. Quote Link to comment Share on other sites More sharing options...
walleyeking Posted February 22, 2017 Report Share Posted February 22, 2017 http://store.do-itmolds.com/Football-JigbrSz-38brHk-570-or-575brCollar-Barb_p_481.html Quote Link to comment Share on other sites More sharing options...
mark poulson Posted February 23, 2017 Author Report Share Posted February 23, 2017 On 2/21/2017 at 6:14 PM, walleyeking said: http://store.do-itmolds.com/Football-JigbrSz-38brHk-570-or-575brCollar-Barb_p_481.html Thank you. Quote Link to comment Share on other sites More sharing options...
cadman Posted February 27, 2017 Report Share Posted February 27, 2017 5 hours ago, Bob La Londe said: Drill the mold and gentley press in a cylinder magnet. Thanks Bob. Why didn't I think of that. I'll try it some day. Quote Link to comment Share on other sites More sharing options...
Mr B Posted February 27, 2017 Report Share Posted February 27, 2017 Great idea Bob. Quote Link to comment Share on other sites More sharing options...
Walking Dead Posted February 27, 2017 Report Share Posted February 27, 2017 I use the magnet strips and they stay put. This is the Swing jig mold but with some trimming it will work. Score the hook indents you make after you squeeze the mold close with the hooks in and they will assist in holding the hook in place. 4 Quote Link to comment Share on other sites More sharing options...
mark poulson Posted February 27, 2017 Author Report Share Posted February 27, 2017 1 hour ago, Bob La Londe said: Just remember that magnets tend to be more brittle than steel or aluminum. A hole you could easily press a stainless steel pin into would cause a magnet the same size to shatter. You can drill the holes a little oversized, and use a little JB weld to seat the magnets so you won't fight to get them in without breaking. Quote Link to comment Share on other sites More sharing options...
mark poulson Posted February 28, 2017 Author Report Share Posted February 28, 2017 (edited) I've used these magnets and they work well: https://www.apexmagnets.com/1-4-x-1-8-disc Edited February 28, 2017 by mark poulson clarify Quote Link to comment Share on other sites More sharing options...
SW Lures Posted March 4, 2017 Report Share Posted March 4, 2017 I use a egg shape from Do-It with multi size cavities. I have modified this one for oversize hooks and have used sheet metal magnets used for holding sheets at angles. Its very strong but somewhat of a pain. This idea of cylinder magnets is a great idea. Specially for molds that you would use often with fine hooks. I agree with y'all about multi cavities being a pain in the....... But for me and this mold, it serves its purpose. Dale Quote Link to comment Share on other sites More sharing options...
