robbor Posted January 18, 2018 Report Share Posted January 18, 2018 I need a plastisol hand mold injector, who's making a good one now? Quote Link to comment Share on other sites More sharing options...
Anglinarcher Posted January 18, 2018 Report Share Posted January 18, 2018 Lots of good ones, just depends on what you want. I think I would prefer the locking style of head, but all most of them work if you are careful and use protective gloves and full length shirts, and I suggest safety glasses. http://www.basstackle.com/category_s/78.htm http://www.tacklewarehouse.com/Do-it_Soft_Plastic_Injector/descpage-DOITSPINJEC.html The above two are NOT the only ones. But, this will get you looking for now. 1 Quote Link to comment Share on other sites More sharing options...
Driftwood Posted January 18, 2018 Report Share Posted January 18, 2018 Ditto on the locking head. Also, get one large enough for your mold shots. 2 Quote Link to comment Share on other sites More sharing options...
Anglinarcher Posted January 18, 2018 Report Share Posted January 18, 2018 28 minutes ago, Driftwood said: Ditto on the locking head. Also, get one large enough for your mold shots. Ya, not just the cavity, but the sprue or runner volume to the cavity(s). Many of us have though that the 4 oz is plenty, and it may be, because our bait is 1/8 oz. But, if you have 6 baits in the mold, that is 1.5 oz and if the runner takes 4 oz you don't have enough. Better too big then too small. 1 Quote Link to comment Share on other sites More sharing options...
robbor Posted January 18, 2018 Author Report Share Posted January 18, 2018 Lol they don't make an injector large enough for my mold. It's 5 cavity ,I'm not even sure yet if 10 oz will shoot all 5 -16" worms Quote Link to comment Share on other sites More sharing options...
Anglinarcher Posted January 18, 2018 Report Share Posted January 18, 2018 1 hour ago, robbor said: Lol they don't make an injector large enough for my mold. It's 5 cavity ,I'm not even sure yet if 10 oz will shoot all 5 -16" worms I don't think they call yours a "hand inject mold". LOL Looks like you must have a shooting star or something like it???? Quote Link to comment Share on other sites More sharing options...
hpssports Posted January 19, 2018 Report Share Posted January 19, 2018 10oz. should be enough to fill it. We have some 20 cavity 8" worm custom bookshelf molds & it takes around 13-14oz. to fill. Don't know the diameter of the worms your shooting but it shouldn't take much over 1/2 of what it takes to shoot 20 8" worms. Quote Link to comment Share on other sites More sharing options...
Cub48 Posted January 19, 2018 Report Share Posted January 19, 2018 The Basstackle injector is a good one might look at the twin setup it will run u about 200.00 i think in the 6 oz injector . It might save u money in the long run. I have a injector 4 oz i bought the mixing block but they won't sell me the rest of the setup so i have spent about a 100.00 and will have to spend 200.00 more if i get the twin. I have ordered a twin setup off ebay it has not come in yet i will let u know how well it is made when i get it been almost a month may of blowed another 100.00 and still not have what i want. LOL Cub48 Quote Link to comment Share on other sites More sharing options...
Apdriver Posted January 19, 2018 Report Share Posted January 19, 2018 Oh yeah. 6 oz. will probably do it. Quote Link to comment Share on other sites More sharing options...
Les Young Posted January 19, 2018 Report Share Posted January 19, 2018 I love my 6 oz. basstackle, but i'm gonna buy a 9 oz. too. Quote Link to comment Share on other sites More sharing options...
robbor Posted January 19, 2018 Author Report Share Posted January 19, 2018 I'm looking at making an all teflon injector in a few months, I just need to shoot some worms now for a trip to Florida Quote Link to comment Share on other sites More sharing options...
robbor Posted January 19, 2018 Author Report Share Posted January 19, 2018 I just unpacked my mold. taped the spru and filled half with water but the tails were mostly empty and i was ia 5oz of water. So a solid 10 oz might work but more than likely me a little short. Ill call bass tackle tommorrow and see if they will make one a little bigger 11-12oz Quote Link to comment Share on other sites More sharing options...
mark poulson Posted January 19, 2018 Report Share Posted January 19, 2018 Could you use a twin injector with the same plastic in both sides? That would give you 12 oz. of plastic. 1 Quote Link to comment Share on other sites More sharing options...
Frank Posted January 19, 2018 Report Share Posted January 19, 2018 5 hours ago, robbor said: I just unpacked my mold. taped the spru and filled half with water but the tails were mostly empty and i was ia 5oz of water. So a solid 10 oz might work but more than likely me a little short. Ill call bass tackle tommorrow and see if they will make one a little bigger 11-12oz You will never get the whole amount out of an injector. At the end you will get plastic that has started to cool to much. Your best bet is see if Basstackle will sell you two of there 10oz one with a Twinjector set up. It will be big but will work well and give you plenty of Plastic. Not sure what you use to heat Plastic but it will work in a presto just fine. Both of the injectors with the same color. 1 Quote Link to comment Share on other sites More sharing options...
hpssports Posted January 19, 2018 Report Share Posted January 19, 2018 You can also make a spacer to block off a few cavities & just shoot a couple of worms at a time. 2 Quote Link to comment Share on other sites More sharing options...
robbor Posted January 20, 2018 Author Report Share Posted January 20, 2018 10 hours ago, hpssports said: You can also make a spacer to block off a few cavities & just shoot a couple of worms at a time. ya thats the way the mold maker did it to test. he only shot 2 cavaties Quote Link to comment Share on other sites More sharing options...
Anglinarcher Posted January 20, 2018 Report Share Posted January 20, 2018 23 hours ago, robbor said: making an all teflon injector in a few months Any idea if you will sell these, and if so,how much? Quote Link to comment Share on other sites More sharing options...
robbor Posted January 20, 2018 Author Report Share Posted January 20, 2018 no just making for me. I already made one with plunger and tip in teflon. but i could not find it when i grabbed my mold. Quote Link to comment Share on other sites More sharing options...
Caden12345 Posted May 15, 2019 Report Share Posted May 15, 2019 Did bass tackle sell anything bigger than a 6 oz I have a 8" fluke mold 3 cavities and a 4 oz injector right now and it fills like 1/4 of the whole mold Quote Link to comment Share on other sites More sharing options...
STO76 Posted May 16, 2019 Report Share Posted May 16, 2019 Check out Quality Injector & More. They are on Facebook and may have a website. Newer company makes all the way up to a 20oz. injector. Quote Link to comment Share on other sites More sharing options...
Canga~ Posted May 16, 2019 Report Share Posted May 16, 2019 I have a 12oz from them and it’s great ( other than the o-rings), quality construction, heats up quickly and keeps the heat nicely. 7 hours ago, STO76 said: Check out Quality Injector & More. They are on Facebook and may have a website. Newer company makes all the way up to a 20oz. injector. 1 Quote Link to comment Share on other sites More sharing options...
Les Young Posted May 18, 2019 Report Share Posted May 18, 2019 I just bought a 10oz. basstackle injector last week. I have a 6 oz. & a cheaper, but smaller twin injection system too. The 10 oz. lets me shoot my brush hog, super hog & beaver style baits in one shot now. As usual the basstackle injector is great. Quote Link to comment Share on other sites More sharing options...
Canga~ Posted May 18, 2019 Report Share Posted May 18, 2019 3 hours ago, Les Young said: I just bought a 10oz. basstackle injector last week. I have a 6 oz. & a cheaper, but smaller twin injection system too. The 10 oz. lets me shoot my brush hog, super hog & beaver style baits in one shot now. As usual the basstackle injector is great. When I was looking for a large injector basstackle didn’t have one listed and did not respond to a couple emails asking about the 10oz availability. It’s still not on the site. I would have probably gotten one of those, but glad I got the quality injector since it’s much shorter than the basstackle and looks less awkward to handle (IMO) 1 Quote Link to comment Share on other sites More sharing options...
Les Young Posted May 24, 2019 Report Share Posted May 24, 2019 On 5/18/2019 at 1:46 PM, Canga~ said: When I was looking for a large injector basstackle didn’t have one listed and did not respond to a couple emails asking about the 10oz availability. It’s still not on the site. I would have probably gotten one of those, but glad I got the quality injector since it’s much shorter than the basstackle and looks less awkward to handle (IMO) I called them & asked specifically about the 10 ouncer & Sarah walked into the shop & said they only had two. Luckily i got one of them.She did say they weren't listed on the website & sent me a link to it. 1 Quote Link to comment Share on other sites More sharing options...
Canga~ Posted May 24, 2019 Report Share Posted May 24, 2019 Hmm, wonder if they still have the other one! Quote Link to comment Share on other sites More sharing options...
