The Jig Is Up Posted July 10 Report Share Posted July 10 (edited) Hello all, I am trying to build a very specific kind of jig, to suit the kind of fishing that I do in my region. To be specific, I'd like to build a weedless micro jig that has an extremely slow rate of fall, like you'd see with a 1/16 oz weedless ballhead jig with a finesse TRD trailer on it. I like the rate of fall that said 1/16 oz ballhead jig has, but I want a jig that is more suited to come through grass. The 90-degree eye of my ballhead jig snags grass a little too easily. To be candid, I would go with the Snootie Jig hands-down, since it goes through grass so well. However, that jig only goes down to 1/8 oz, so I'm not sure if it would fall slow enough for what I'm looking for. Any ideas for a weedless jig that fits those requirements? I have been brainstorming this jig for some time, and have yet to find one that exactly ticks all the right boxes. Thank you! Edited July 10 by The Jig Is Up Quote Link to comment Share on other sites More sharing options...
cadman Posted July 10 Report Share Posted July 10 Pour the 1/8 oz Snootie jig in tin. More than a third less weight than lead. Lead 11.342 grams per cubic centimeter Bismuth 9.87 grams per cubic centimeter Pewter 8.5-9.5 grams per cubic centimeter Tin 7.265 grams per cubic centimeter 3 Quote Link to comment Share on other sites More sharing options...
cadman Posted July 10 Report Share Posted July 10 How about Do-It's BAT-7-A, Bat Jig Mold #3504. Maybe you can modify the hook eye to fit your hook. 2 Quote Link to comment Share on other sites More sharing options...
The Jig Is Up Posted July 10 Author Report Share Posted July 10 (edited) @cadmanThose are both amazing suggestions. I have never poured with tin before... I assume that requires a dedicated hot pot... I may have to give that a try. The Bat Jig is another incredible suggestion. That jig does not come with any kind of weedguard, but I think tying a wire weedguard in would be fairly trivial to do. The Do-It Walleye Head Jig (WHJ-7-AR) is kind of in the same boat - no weedguard slot, but it has a nice streamlined design and goes down to 1/16 oz. Edited July 10 by The Jig Is Up Quote Link to comment Share on other sites More sharing options...
Jig Man Posted July 10 Report Share Posted July 10 It’s easy to make a weedguard slot. All you have to do is cut a piece of wire just bigger than the weedguard, tape it in place, put the mold. In a vice and tighten it down. I have several molds modified this way using Sevalon or Surflon wire in 25, 60 and 90#. 1 1 Quote Link to comment Share on other sites More sharing options...
cadman Posted July 10 Report Share Posted July 10 1 hour ago, The Jig Is Up said: @cadmanThose are both amazing suggestions. I have never poured with tin before... I assume that requires a dedicated hot pot... I may have to give that a try. The Bat Jig is another incredible suggestion. That jig does not come with any kind of weedguard, but I think tying a wire weedguard in would be fairly trivial to do. The Do-It Walleye Head Jig (WHJ-7-AR) is kind of in the same boat - no weedguard slot, but it has a nice streamlined design and goes down to 1/16 oz. On the bismuth or tin, all you have to do is empty your current pot of lead and put in the tin or bismuth. If you are going to do a couple of jigs for samples, take an old tablespoon or a small ladle, put a small chunk of tin, and heat the spoon/ladle with a torch and pour it into a hot mold. You can heat the cavity of the mold with a torch to to warm it up as well. Tin has a low melting point about 425 degrees lower than lead. I don't know how strong it is though. Bismuth is very hard, as I have poured bismuth jigs for the guys in Massachusetts. On the jigs, the walleye jig has a 90 degree hook, so I don't know if that is an issue for you. The other two are 60 degree hooks. You can incorporate a weedguard slot like Jig Man mentioned it is not complicated. 2 Quote Link to comment Share on other sites More sharing options...
Ogajiga Posted July 17 Report Share Posted July 17 How about weightless T-rig Gamakatsu EWG worm hooks? Available in sizes #4 - 5/0. Can be weighted with an inline worm weight or split shot. Quote Link to comment Share on other sites More sharing options...
Brushhog Billy Posted Sunday at 12:02 PM Report Share Posted Sunday at 12:02 PM Poisontail mold has a 1/8 ounce with a small weedguard Quote Link to comment Share on other sites More sharing options...
21xdc Posted Sunday at 03:11 PM Report Share Posted Sunday at 03:11 PM This would be my choice https://store.do-itmolds.com/Casting-JigbrSz-18-316-14brHk-32886brCollar-Ring-amp-Barb_p_947.html 1 Quote Link to comment Share on other sites More sharing options...
